Small projects completed

I got a few small house projects completed this weekend, quite a few I got from Pinterest.

First was this spice rack on the inside of a pantry door. Here's the "pin":

Here's my version: 

Next was this custom utensil insert:

Here's mine:

The next two weren't found on Pinterest. First, I replaced the toilet paper holder in the grey bathroom because a normal sized toilet paper roll wouldnt fit on it and actually spin: 

Before

After:

Lastly, I added a clothes rod to the laundry room so that clothes could be hung up in there that needed to hang dry: 

One last laundry post....

Added the second laundry shelf over the weekend. The contact paper is possibly temporary, not sure if it works for me. But for now, it works.

The laundry "room"

So, after getting the dryer vent issues fixed, I figured we might as well keep making the laundry area more functional. So, I repaired the leaky hot water valve, replaced the washer hoses with these super-duper reinforced hoses that as supposedly better than stainless steel:

I also put a plastic tray under the washing machine -- just in case.

Next, I repainted the alcove in the same color as the living room, Cornerstone. We had two gallons of it left over.

Before:

Progress:

Two shelves will be going up (one is actually already in place, but don't have a photo at the moment).

Here is a pic of the dryer vent routing now -- much better:

Dryer Venting part two of two

So after I realized our dryer vent was out of code, I went to work on it on Saturday. This first step involved cutting away the sheet rock to get better access to it:

One problem with this dryer vent is that there is nothing to attach the pipe from the dryer to (there is no flange). You basically just stick the dryer vent in that hole, which doesn't impress me. 

Next, I climbed into the attic. It was a bit like an Indiana Jones movie as far as the cob webs went: 

But I hacked my way to the dryer vent coming up from below. And pleasantly found that what I thought was the dryer vent in the back of the house was not. The dryer vent went up through the roof and vented above. Very cool.

However, it was still not up to code. There was about five feet of flexible 3" pipe. Code is 4 inch and should not be flexible. I climbed up onto the roof to inspect the venting and found this:

That perfectly cut hole is, I think, from the dryer snake I used a few days ago ----- about the perfect size. 

I ended up pulling out all of the dryer vent, and replacing it with 4" round solid tubing in 5 foot sections. Additionally, I cleaned out all of the lint from the roof vent and put in a standard elbow at the dryer side to make attaching the vent from the dryer easier. Not super impressive, but this is the new pipe coming up into the attic and making a slight bend to exit out the roof. 

Here it is exiting:

While I was up on the roof, I removed one of two non-functional satellite dishes, swept the leaves off, cleaned out some of the gutters and took off our above pictured "Home Saver Pro" ----- chimney cover. And gave her a good cleaning, coat of rust inhibiting primer and a final coat of rust inhibiting charcoal grey paint. 

Lastly, I made a cover out of wood to repair the square hole I cut into the wall:

Dryer Vent re-routing

Not the sexiest topic on this blog, but my next project is going to be re-routing the dryer vent. Most city codes allow for 25 feet of straight dryer duct. However, each 90 degree bend counts as 5 feet. I estimate that our current vent has four 90 degree bends (20 feet) plus about 30 feet of straight pipe = 50 feet. The dryer vent goes into the wall, up into the attic, across the attic, down through the back wall of the house and then out onto the back patio.

So I bought this dryer vent snake:

And used it last night = disturbing. It's basically a 12 foot flexible plastic shaft that has an auger brush on the end that you attach to a drill. I put the snake up the dyer vent and hit a blockage about 2 feet in. I pushed through that blockage and a ton of dryer lint came falling down. Then I got the snake another 5 feet in and hit another blockage, and so on until I had used up my 12 feet of snake length. I ended up with half a paper garbage bag full of old dryer lint that was stuck in 12 feet of our dryer vent. This confirms my theory that being out of code on these sorts of things are scary.

Re-routing the Vent

My plan was to run the vent down into the crawlspace then out the front of the house. However, there is foundation under the wall where the dryer vent goes and very little crawl space, so that is out.

As a result, I'm going to go up and into the attic and then out the front.  This will mean only one bend and much less straight pipe as well. However, it's actually not even going to have a bend. How? I bought this gradual 90 joint called an "Ell" (har har) which is meant for dryer venting and is made so that code considers it a straight pipe and not actually a bend:

Additionally, I'll be using something called the dryerbox:

This gets mounted into the wall and the venting tube from the dryer attaches to this. So that the vent from the dryer doesn't get crushed. Currently, the flexible tubing from the dryer is getting crushed in order to close the laundry doors. By mounting this countersunk box, the moist air can escape much more easily. 

If you have some inkling that this is in the realm of tin foil helmet paranoia, take a look at this list of recent dryer fires across the country: http://www.dryerbox.com/dryer_fire_articles.htm

Dryer fire leaves Amherst family homeless

Tony Ellis, the father, said the dryer started smoking. Ellis said he thought he had succeeded in putting out the fire with a fire extinguisher, but smoke started coming from a wall. Cathy Ellis said her husband yelled for everyone to get out of the house. “I just thank God that all my kids got out,” she said.

Jake Ellis, 20, grabbed his 11-year-old sister Alyssa, who is paralyzed and cannot speak, and carried her out of the two-story home.

And if you have a dryer vent that doesn't immediately go outdoors, get the lint snake and see if you have major blocks of lintage in your line.